Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
On this page down the page you can discover a bunch of incredibly good guidance on the subject of How to Install a Bathtub.
Setting up a bath tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a new one is likewise a reasonably difficult job. If the old bathtub is conveniently accessible, the job can relocate speedily; if you have to open a wall surface to get rid of the old tub and place the brand-new bath tub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will need an assistant to vacate the old bathtub and also embeded in the new one. Make sure you have qualified on your own for the work and also are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is far better to consider employing one before you begin. Chances are you may need an expert plumber to make tube links.
This post will certainly aid you mount a brand-new tub in your shower room if you have actually currently gotten a brand-new bathtub as well as do not require to alter the plan of your previous water system pipelines.
Your devices as well as product list must make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be quite bothersome because of the restricted access that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric prepared for the staying water that will certainly come from the pipes. Once the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipes.
If you need to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in place between the faucet and also the sink. Secure the tap in position with the supplier offered backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The previous kind needs to be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Tub
Utilizing both wood boards under its feet, position the bathtub in the required setting. The wood boards are practical in equally spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 little factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the tub up until the level checks out degree.
To set up faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression join; then do the same for the other tap.
Switch on the supply of water and check all joints and new pipework for leaks and tighten them if necessary. Load the bath tub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Finally, repair the bathroom paneling as defined in the producer's instruction manual. Tiling and sealing around the bath tub needs to wait till the tub has been used at least when as this will certainly resolve it into its final position.
Planning for the Installment
To start with, the sustaining frame supplied with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to enable the activity experienced when the tub remains in usage. The sealant can split rather early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily offered on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading about Installing A Bathtub? Try leaving a comment further down. We'd be interested to listen to your reactions about this page. We are looking forward that you visit us again soon. So long as you appreciated our page if you please remember to pass it around. Bless you for your time. Don't hesitate to come by our site back soon.
Instant Quote Report this page